Two Hole Strap for EMT Conduit: Sizes, Dimensions, and How to Choose the Right Fit

Choose a two hole strap by matching it to the EMT conduit’s trade size, checking the strap’s actual inside width and mounting-hole layout, and confirming that its material and finish suit the installation environment. A strap marked for 1/2-inch EMT is intended for that trade size; the label does not mean the strap opening measures exactly 1/2 inch. Before ordering, compare the supplier’s dimensional drawing with the conduit outside diameter, mounting surface, fasteners, and project requirements.

If you are looking for more details, kindly visit our website.

This guide is for electrical contractors, distributors, OEM buyers, and project teams sourcing EMT conduit supports. It explains how nominal sizes relate to outside diameter, what dimensions to request, and how to evaluate product and supplier options. Because strap dimensions and available finishes can vary by manufacturer, treat the product drawing and confirmed specification as the final basis for selection.

What a Two Hole Strap Does

A two hole strap is a shaped support that holds conduit against a mounting surface using two fasteners. The curved section sits around the conduit, while the holes allow the strap to be secured to a wall, ceiling, framing member, or other suitable surface. Its purpose is to retain and support the conduit; the correct fastener and installation method depend on the substrate and project requirements.

Two mounting points can help keep the strap aligned during installation, but they do not establish a universal load capacity or support spacing. Those values depend on the product design, fasteners, substrate, conduit arrangement, and applicable project rules. Do not infer a load rating from the number of holes alone.

EMT Sizes and Conduit Outside Diameter

EMT is identified by a trade size, which is not the same as its outside diameter. For example, 1/2-inch EMT has a nominal trade size of 1/2 inch but an outside diameter of approximately 0.706 inch. Use the EMT trade size to identify the general strap size, then confirm the strap’s stated fit and dimensions against the conduit specification.

The outside-diameter figures above are common EMT dimensions, provided as a reference for product selection. Confirm the applicable conduit standard and the dimensions of the specific conduit being installed. For sizes beyond those shown, request the corresponding strap drawing rather than extrapolating from another size.

Dimensions to Check Before Ordering

Conduit fit and inside width

Ask for the strap’s inside width or fit range and compare it with the conduit outside diameter. A strap that is too tight may be difficult to install or may not sit as intended, while excessive clearance can leave the conduit poorly retained. The correct fit also depends on the strap shape and how the product is designed to contact the conduit.

Overall profile and mounting-hole layout

Check the strap’s overall width, height or profile, material thickness, hole diameter, and center-to-center distance between mounting holes. These dimensions determine whether the strap fits the available mounting area and whether the specified fasteners can be used. Request a dimensioned drawing when the hole pattern must align with predrilled supports or an established installation layout.

SIOSAN contains other products and information you need, so please check it out.

Fastener and surface compatibility

Confirm that the hole size works with the intended fastener and that the mounting surface can accept it. Fastener selection is not determined by the strap alone: substrate type, required holding capacity, installation conditions, and project specifications matter. Where those requirements are unclear, consult the responsible installer, engineer, or project authority before purchase.

Materials, Finishes, and Application Matching

Two hole straps may be offered in different materials or protective finishes, depending on the supplier’s product range. Buyers commonly evaluate corrosion exposure, indoor or outdoor use, contact with adjacent materials, appearance, and project specifications when comparing options. Do not assume a particular material or finish is suitable for every environment based on its name alone.

For indoor installations in relatively controlled conditions, a standard product specified for the project may be appropriate. Outdoor, damp, corrosive, or otherwise demanding environments call for closer review of the strap material, coating, and installation details. Ask the supplier to identify the material and finish in writing, and confirm that they meet the project requirements before approving a substitution.

A Practical Selection Framework

1. Identify the conduit. Record the EMT trade size and verify the conduit outside diameter from the applicable specification or product documentation.
2. Define the installation. Note the mounting surface, environmental exposure, required fasteners, available clearance, and any project-specific support requirements.
3. Compare the strap drawing. Check the marked trade size, inside fit, overall profile, thickness, hole diameter, and hole-center spacing.
4. Confirm material and finish. Match these details to the environment and written project specification rather than relying on a general product description.
5. Approve a sample or drawing when needed. For repeat orders, custom layouts, or tight clearances, review a sample or signed-off drawing before production or bulk purchasing.

Common Buying Mistakes to Avoid

• Confusing trade size with outside diameter: A 1/2-inch EMT label does not indicate a 1/2-inch outside diameter.
• Ordering by size label alone: Manufacturers can use different strap profiles, so verify the dimensions that affect fit and installation.
• Ignoring hole spacing: A strap may fit the conduit but fail to align with the mounting pattern or available surface.
• Assuming a finish is suitable: Request material and finish details and compare them with the environment and project specification.
• Assuming support capacity: Do not infer load ratings or allowable spacing without product documentation and project guidance.

Pricing, MOQ, Lead Time, and Supplier Evaluation

Pricing can depend on the strap size, material, finish, order quantity, packaging, and whether a standard or custom specification is required. Minimum order quantities and lead times also vary by supplier and product configuration; they should be confirmed in a current quotation rather than assumed from a catalog listing. For a comparable quote, send the size breakdown, estimated quantity per size, required finish, drawing requirements, destination, and preferred packaging.

When evaluating a supplier, ask whether it can provide a dimensioned drawing, clearly identify material and finish, support size-specific quotation, and confirm the order’s production and delivery terms. For a custom requirement, establish which dimensions may be changed and request written approval of the final specification. These steps help reduce ambiguity between the intended conduit fit and the product delivered.

How SIOSAN Can Support Your Sourcing

SIOSAN works with B2B buyers sourcing conduit-related products and can review the requested size, dimensions, material, finish, and order quantity for quotation. Share your EMT trade sizes and any existing drawing or project specification so the product requirements can be checked before an order is placed. Availability, customization, minimum order quantity, and lead time should be confirmed for each specific request.

Key Takeaways and Next Steps

• Use EMT trade size to identify the general strap size, but verify the actual strap fit and drawing dimensions.
• Check inside width, profile, thickness, hole diameter, and hole-center spacing against the conduit and mounting surface.
• Specify the required material and finish based on the project environment and written requirements.
• Confirm fasteners, support requirements, MOQ, pricing, and lead time with the supplier before ordering.

The right two hole strap for EMT conduit is the one whose documented dimensions fit the conduit and mounting layout, and whose material and finish meet the installation specification. Start by preparing a size-by-size requirement list, then compare it with a supplier drawing and quotation. Contact SIOSAN with your EMT sizes, quantities, application conditions, and any required dimensions to discuss a suitable sourcing option.