A standard padel single court measures 20 m long by 6 m wide, providing a playing area of approximately 120 m². The court uses the same 20 m length as a conventional doubles court but is narrower, making it suitable for one-on-one play and sites with limited width. Before ordering a court enclosure, I recommend confirming the applicable rules, clearances, access routes, drainage requirements, and local building regulations.
Click here to get more.
| Item | Typical dimension or requirement | Planning significance |
|---|---|---|
| Playing length | 20 m | Defines the longitudinal court layout |
| Playing width | 6 m | Provides the narrower singles playing area |
| Playing area | Approximately 120 m² | Used for preliminary surface and site calculations |
| Net height at posts | Approximately 0.92 m | Supports the net installation specification |
| Net height at center | Approximately 0.88 m | Allows the net to follow the standard profile |
| Minimum unobstructed height | 6 m in standard court guidance | Important for indoor halls, lighting, and overhead equipment |
These figures describe the playing court rather than the full construction site. The International Padel Federation (FIP) identifies the padel court as a rectangular playing area and provides the technical rules used as the principal reference for court geometry and equipment. Because regional facilities may apply additional accessibility, safety, fire, or construction requirements, I treat the FIP rules as the technical starting point rather than a substitute for local approval.
A padel single court is a narrower version of the court intended for singles play. Its standard playing footprint is generally 20 m by 6 m, while a conventional doubles court is typically 20 m by 10 m. The reduced width can help operators use constrained sites, but the enclosure, surface, lighting, circulation, and maintenance requirements still need to be designed as a complete system.
The court combines a sports surface, net system, perimeter fencing, wall or panel elements, gates, lighting, and structural supports. The enclosure keeps the ball within the playing environment and defines the boundaries used by players. For a wire mesh supplier, the fencing system must balance visibility, ball containment, corrosion resistance, structural stability, and safe finishing.
Single courts may be considered for private facilities, training venues, sports clubs, hotels, schools, residential developments, and compact urban projects. They can be useful where a full 10 m court width is difficult to accommodate or where the owner specifically wants a singles format. I recommend confirming the intended playing format before procurement because a narrower court may not support standard doubles use.
The playing area alone is approximately 120 m², but the project site must be larger than 20 m by 6 m. Space is needed for structural posts, wall and mesh assemblies, doors, player access, maintenance, drainage, lighting equipment, and safe movement around the enclosure. A practical preliminary layout should therefore reserve a perimeter allowance and then be checked against the selected court system and local regulations.
There is no single universal site envelope that applies to every supplier, because construction details and safety rules vary. As an initial feasibility exercise, an owner may draw the 20 m by 6 m playing rectangle and add several metres around it for circulation and service access, but this should not be treated as a final compliance dimension. I recommend asking the supplier for a dimensioned general-arrangement drawing before finalizing foundations or concrete works.
Indoor projects also require adequate clear height above the court. FIP-based guidance commonly uses a minimum unobstructed height of 6 m for a standard court, while an indoor venue may need additional space for lighting, roof structure, ventilation, sprinklers, and maintenance access. The venue designer should verify the complete vertical section rather than checking only the nominal court height.
The base should be sufficiently level, stable, and engineered for the selected surface and anchor system. Outdoor courts need a drainage strategy that prevents standing water from affecting the artificial turf, shock pad, concrete base, or metal components. Delivery vehicles and installation teams also require a route wide and strong enough to handle the packaged panels, posts, mesh, glass or wall elements, and lifting equipment.
Dimensions are only one part of a purchasing specification. I suggest confirming the court length and width, net geometry, wall heights, mesh height, gate location, post spacing, anchoring method, surface build-up, lighting position, and corrosion-protection system in one approved drawing. This approach reduces the risk of ordering components that are individually correct but incompatible as a complete enclosure.
For wire mesh, the buyer should request the wire diameter, aperture size, panel dimensions, coating type, coating thickness where applicable, edge treatment, weld quality, and fixing method. The correct specification depends on the court design, ball-impact requirements, local climate, and whether the installation is indoor, coastal, humid, or exposed to industrial pollutants. I avoid selecting mesh solely by appearance because aperture, wire size, frame stiffness, and corrosion protection all affect service performance.
Boya Product Page
Boya can support project discussions around welded wire mesh, perimeter panels, posts, fittings, and customized packing requirements, subject to the agreed technical drawing. We can review the required court dimensions, material grade, surface treatment, panel configuration, and destination conditions before preparing a quotation. Final suitability should be confirmed through the approved design and any project-specific engineering requirements.
The net is normally specified by its length, height profile, tensioning system, posts, and anchoring details. Standard guidance commonly places the net at approximately 0.88 m in the center and 0.92 m at the posts, but the buyer should verify the current governing rules and the selected system. The playing surface should also be reviewed for sub-base compatibility, drainage, grip, ball response, maintenance, and replacement planning.
I recommend starting with the intended use rather than choosing components independently. A private training court may prioritize compact access, simple maintenance, and cost control, while a commercial facility may place greater emphasis on durability, appearance, lighting, spare parts, and cleaning access. The selected configuration should match the expected operating hours, weather exposure, user volume, and maintenance resources.
For international sourcing, I also recommend checking the commercial specification alongside the technical specification. Important details include minimum order quantity, production lead time, inspection arrangements, packaging method, spare mesh panels, replacement fittings, and the agreed Incoterm. These items can affect the project schedule as much as the court dimensions themselves.
The most common planning error is treating 20 m by 6 m as the complete construction footprint. This measurement describes the playing area, while the finished installation also includes posts, enclosure components, doors, circulation, and service space. I recommend using a supplier-approved layout before setting out foundations or ordering surfacing materials.
A 20 m by 10 m court is widely associated with standard padel doubles play, but it is not the same as a 20 m by 6 m singles court. Ordering the wrong width can create unnecessary material costs, redesign work, or a facility that does not meet the intended operating model. The purchase order should state the playing format and finished internal dimensions in metres.
Indoor and outdoor courts face different risks. Outdoor projects may need stronger attention to wind exposure, rainwater drainage, ultraviolet exposure, and corrosion, while indoor projects may require coordination with roof loads, lighting, ventilation, sprinklers, and access equipment. A mesh and post system that is suitable in one environment may require a different coating or structural arrangement in another.
For court geometry and equipment terminology, I recommend beginning with the International Padel Federation (FIP), Rules of Padel. The FIP rules are the primary international reference for padel court dimensions, net requirements, playing layout, and enclosure-related provisions. Buyers should also consult the relevant national federation, sports governing body, building authority, and project engineer because local requirements may be stricter or more detailed.
For facility planning, the Lawn Tennis Association (LTA), Padel Court Guidance is another useful industry reference for understanding court construction and venue considerations. These sources should be checked in their current editions because technical guidance can be revised. When I prepare a wire mesh quotation, I use the buyer’s approved dimensions, application environment, and governing project specification as the basis for the final product recommendation.
The direct answer is that a padel single court normally uses a 20 m by 6 m playing area, or about 120 m². However, the actual project requires additional space for the enclosure, access, foundations, drainage, lighting, and maintenance. I recommend treating the 20 m by 6 m figure as the starting court dimension, not the complete site footprint.
Your next step should be to provide the supplier with the intended playing format, indoor or outdoor location, climate conditions, finished court dimensions, mesh requirements, delivery destination, and installation constraints. Boya can review these details for a wire mesh and perimeter-enclosure quotation, including material options, surface treatment, panel configuration, packaging, and technical documentation. Requesting a dimensioned drawing before production is the most reliable way to align the court size, foundation plan, and supplied components.
Are you interested in learning more about Padel Single Court Size? Contact us today to secure an expert consultation!