There are many benefits to using pneumatic actuators due to their supply of energy. Because they use air to operate the system, they are a simple design and have very high safety ratings in comparison to their counterparts; hydraulic and electronic.
The Pneumatic Actuator can be triggered manually, through pressure or through temperature changes; for example, when a machine is overheating, it will heat the air in the compressed chamber and cause the air particles to expand thus setting off the actuator and causing a valve movement. This way, the actuator is automatic which can be useful on industrial sites needing to be temperature-controlled.
As there are so many, here are the main benefits to using a pneumatic actuator as they are:
More economical
Electric actuators use a lot of energy, which they either loose as excess heat or require for the gearboxes. On the other hand, pneumatic actuators act directly on the shut-off device. Pistons and an actuator shaft are sufficient for the conversion of the linear compressed air force into a swivel motion. As compared to electric actuators, pneumatic solutions are more economical as they only need power for the generation of compressed air and for open-loop control. Actual movement is created through the compressed air.
Durable and low maintenance
For years, pneumatic actuators have proven to be resistant to vibration and to be durable as they are made from a small number of components and are thus less likely to break down. In addition, they are also resistant to continuous loads and remain maintenance-free over their entire service life. Oil changes or additional lubrication are unnecessary.
Since pneumatic actuators have overload protection and a higher actuation force can be achieved very simply by increasing the pressure, it is often possible to use smaller sizes with a lower weight. Pneumatic systems are able to deliver high forces of up to 50,000 N and torques of up to 10,000 Nm.
Fail safe
Pneumatic actuators are safe as there are no environmental hazards from liquid leaks or sparks. Compressed air is also available in the event of a power failure. Alongside a compressor for generation and treatment purposes, an air reservoir is always available for emergencies. Furthermore, being overload-proof and explosion-proof also mean that they also used in fail-safe, extreme environments and critical applications without compromising performance and safety.
In addition to the benefits stated above, pneumatic actuator also provide other advantages:
They can withstand high temperatures
They have no magnetic interference
They are lightweight as there is no liquid
They offer high precision-control positioning and accuracy in linear motion
They are quieter than other actuators such as hydraulic
So, having a pneumatic system instead of an electric or hydraulic system proves to be a more economic, hassle-free and safe option for all applications. They are also reliable for long periods of time.
But, before you head to SLS to find a pneumatic actuator in Singapore, you’ll also need to know that there are some limitations.
What are the Limitations of Using a Pneumatic System?
Pneumatic systems are not for every application. There are industries and areas where an electric or – safer – hydraulic actuator would provide a bigger benefit due to speeds.
For a pneumatic actuator to be at its most efficient, it must be sized and fitted to the job. Meaning there could be more costs involved.
Often, specific jobs require high-speed valve or object movement rather than slow-paced. In these situations, hydraulic presser is a preferred energy. This is because compressed air can also experience leaks and losses causing the actuator to have a lower pressure and a slower force.
Not only this, but the compressed air can become mixed with other compartments to the cylinder such as lubricants or oils, making the compression function at slower speeds. This is one of the reasons why you need to research into the brand and use providers such as SLS in Singapore to point you in the right direction.
So, even though pneumatic pressure has its many positives, make sure that the actuator is right for your needs.
Which Industries Are Likely to Use the Pneumatic Actuator?
With this, there are many industries across the globe that will use pneumatic actuators to power their everyday essentials.
Water treatment plants
Water treatment plants, for example have 30% of their valves controlled by pneumatic systems. They are used within the instruments, sensors, valves, and filter membranes, too. With the vast real estate of water treatment plants, monitoring systems can slow the bandwidth, so using a compressed air module that can be monitored locally, is a benefit to the overall system.
Chemical and processes industries
Chemical and processes industries use the pneumatic actuators simply in valving to control the flow of chemicals. As these industries often perform dangerous tasks such as handling hazardous or even toxic chemicals, the pneumatic actuators are commonly used to ensure safety and reliability. As mentioned above, their benefits include their ability to withstand high temperatures and durability. That’s why these are a common choice within gas, steam and thermal power plants.
Manufacturing industry
While it is a broad spectrum of processes, there will almost always be space for a pneumatic actuator in the manufacturing industry. They’re used within manufacturing due to their durability and low-maintenance needs. As a manufacturing plant
is large, owners require moving parts that will last a long time without the need of topping up or maintenance which are needed with the hydraulic and electric systems.
Food handling industry
With hydraulic fluid or electricity, the chance of leaking and contaminating the food is much higher than the chance of compressed gas leaking and causing slowed manufacturing. With food it can be imperative to have durable actuators that will cause food contamination or cause sparks. This is why much of the food processing industry will make use of the pneumatic systems.
Electronic Industry
Handling, assembling and testing small parts are at the heart of the electronics industry. Production and assembly of electronic components such as semiconductors is fast-paced and requires precision. With a pneumatic system in place, it is capable of high-speed and accurate positioning, despite the high moving mass. As the product cycles in the electronic industry is becoming ever shorter, pneumatic also provides a more economical solution in the long term than its hydraulic counterpart.
But, there’s more. Pneumatic actuators are part of most industries you experience. Here’s some other examples where you’ll find the pneumatic systems at work:
Agriculture
Automotive
Laboring
Packing
Amusement Park Machines
Coal Mining Equipment
Textile Industry
Bicycle Pumps at Home
But, there’s also many areas within the home that you’re probably unaware of, for example doors, lawn mowers, under-bed storage, air conditioning and more.
In a Nutshell
From the costs, through the safety aspects and on to the ease of operation, pneumatic actuators offer clear advantages in a wide range of applications across many industries. However, it is also important to note that it is not one size fits all.
Is Pneumatic Actuator the Right Fit for Your Application?
Let SLS help you to find the right solution! If you would like to know if pneumatic actuator is the right fit for your industry or application, please contact us today by clicking on the button below and our friendly engineers will get in touch with you: